A Portland retailer built a pear-shaped bridal line that sold out in six weeks, then reordered and found the new parcel read wider and blunter than the first. Clients comparing the two rings side by side in the store noticed. The supplier had swapped cutting centers between lots and said it was ‘within tolerance.’ For a retailer whose brand rests on consistency, that is not tolerance—that is a problem. This is how a pear moissanite wholesale order should be controlled, and what you should ask before you reorder.
Where pear cuts go wrong in bulk
The pear is a hybrid of round and marquise: a rounded shoulder on one side, a tapered point on the other. That shape is beautiful on the finger but unforgiving at the bench. The two failure points are asymmetry (one shoulder larger than the other) and point bluntness (the tip looks worn rather than sharp). Both read as ‘off’ to a trained shopper even when they cannot say why.
| Pear defect | How it shows up | Our control |
|---|---|---|
| Shoulder asymmetry | Rings look lopsided when worn | Measured left/right within 3% |
| Blunt point | Tip reads rounded, not sharp | Point angle verified per stone |
| Off L/W ratio | Does not fit pear mounts | Documented 1.45–1.55:1 band |
| Point chipping | Tip damages under setting | 9.25 Mohs + pre-setting edge check |
How we build a pear lot
We cut pears to a 1.45:1–1.55:1 length-to-width ratio, the classic silhouette that elongates the finger. Every stone is checked for a centered point and balanced shoulders under the loupe. The point is the most fragile part of the pear—we inspect the tip edge before setting and recommend V-prong or bezel protection in our mounting notes. Color ships near-colorless D–F as standard, clarity VVS for solitaires. Moissanite’s 9.25 hardness means the point holds up far better than a softer gem, but it still needs the right seat.
- Sort by carat and lock ratio band for the lot.
- Measure shoulder symmetry and point angle.
- Check tip edge for chips under 10x loupe.
- Grade bow-tie shadow (pears show it too).
- Attach GRA certificate and orientation note to each stone.
Sourcing by your retail model
Test order, pear-curious: Start with 10–15 stones at 1.0–1.3ct. Pear demand is trend-driven, so a small test tells you whether your clientele leans into the shape before you commit. MOQ 10 pieces.
Boutique running a pear campaign: Lock a cutting lot and specify your point orientation (north-south with the point up). We reserve the lot so reorders match. Ask for matched pairs if you also sell pear earrings.
Private label / custom line: We supply pears set in V-prong or bezel mounts, DDP to US/EU, with GRA documentation and a process audited by a third party since 2016. Reorder guarantees apply to locked lots.
Frequently Asked Questions
Which way should the pear point face?
The point faces toward the fingertip (north) in the most popular pear engagement rings. We can mark orientation on the parcel; for earrings, pears are set pointing outward.
Do pear moissanites show a bow-tie?
Yes, pears show a lighter bow-tie shadow across the wider shoulder. We grade it as faint for bridal lots; heavy shadows are excluded.
What carat sells best for pears?
1.0–1.5ct is the bridal sweet spot, where the elongated silhouette reads well without overpowering the hand.
Can you match pears for drop earrings?
Yes. Pairs are matched by weight, color and symmetry from the same lot, with a matching sheet. Pair rejection runs under 1% on controlled lots.
How do I protect the pear point in a setting?
Use a V-prong at the point rather than a standard prong, or a bezel. We include a mounting note with every pear lot so your bench setter knows.
Mounting and bench notes for pears
A pear that looks perfect loose can still fight the bench. The rounded shoulder and the tapered point seat differently, and a setter who treats it like an oval will leave the point unprotected. We ship a one-paragraph mounting note with every pear lot: seat the point in a V-prong, support the shoulder with a standard claw, and avoid over-tightening the basket because the curved girdle does not compress the way a round one does. Tell your setter whether the point faces north on the ring or outward on earrings, and check orientation under the prong before final polish. These notes are free, but they prevent the single most common pear return—a loose or chipped point—which typically runs around 3% on unspecified lots. For a private-label program we can supply the stones already set and oriented, so your bench never touches a bare point.
Takeaways
- Ask for shoulder symmetry and point-angle—not just ‘pear cut.’
- Lock a lot so reorders match your first campaign.
- Specify point orientation on the PO.
- Recommend V-prong setting to protect the tip.
Request a sample parcel: MOQ 10 pcs, ships in 5 business days. Explore the pear cut collection, read the pear buying guide, or review wholesale terms.